Today I am working with the Harlequin pattern. I decided to make a Christmas card since this is about the time of year to get starting. I tried to pick products that are easy to use and come in multiples so you can easily replicate the card 5, 10, or 20 times.
Start by adhering white cardstock to a piece of chipboard.
Cut into squares and run through the Vagabond machine using the Sizzix Ice Skates Bigz die. Cut one skate per card being made.
Cover all skates with Crackle accents and set aside to dry (I did not cover the skate blade).
Once dry, rub Distress Ink into crackle finish.
Lacing the Skate -
1. Thread string through needle.
2. Thread the string through the bottom hole - even out the string.
3. Work your way up the skate, skipping every other lace hole.
4. Starting at the bottom with the other end of the string, work your way up the skate, crossing over the first string.
5. Tie the string into a bow at the top.
I wrapped the string around the boot a few times and then tied the bow. Either way works.
6. Paint the heal of the boot with a thin coat of brown paint. Use your finger tip to rub the paint into the crackle in the heal.
7. Paint the skate with silver Adirondack dabber paint.
8. Add a thin coat of Glossy Accents to the skate and sprinkle with Pumice Stone Distress Glitter. Set aside to dry.
Back to the card -
Cut a piece of Ranger Manila cardstock for a card front. Using the new Harlequin stencil, add Barn Door Distress Ink to the cardstock with a Blending tool.
Because the cardstock was wider than the stencil, I just slid it over, lined up the pattern and began coloring the rest of the cardstock.
Until the entire cardstock is covered.
Wipe off the stencil with a wet wipe. Super easy clean up.
Once clean, line up the stencil over the red pattern.
This time color the open area with a combinations of Forest Moss and Peeled Paint Distress Ink.
Again, slide the stencil over to color the remaining area.
Until the entire cardstock is covered.
Ink the cardstock with Frayed Burlap and the edges with Walnut Stain.
Cut a piece of Core'dinations cardstock to use as the card foundation. Set the card to the side.
Add the large Sized Oval to the center of the Cameo Frame Bigz die. Cut a piece of Merriment paper and run it through the Vagabond machine.
NOTE: I should have adhered the paper to a piece of chipboard before I cut it but I didn't, so I cut the chipboard separately and then glued the two together.
Add the Cameo Frame and the Ice Skate to the card front.
Pick three Christmas words from the Holiday Chit Chat stickers in either white or kraft. One book of will make a lot of cards!
Cut the ends like a flag and add to the card front.
Color a mirrored star with Meadow Alcohol ink. Add a touch of gold mixative over the green. There are 24 stars in 5 sizes in one pack of Mirriored stars...plenty to go around.
NOTE: If you plan to color the stars in one color - Drop the stars into a small plastic bag. Squeeze a small amount of the desired Alcohol Ink into the bag. Close the bag and rub the color around till the stars are coated. Dump out onto a craft sheet and wait a minute or two to dry. Now they are ready for a bit of gold over the top.
Add star to the ice skate with a bit of foam tape.
I used the center that was leftover when I cut the Cameo Frame/Sized Oval for the inside of the card. I also used the Harlequin Layering Stencil and Forest Moss to add a little pattern over the top. A Christmas Word band and a Vial Label finish it out.
The Christmas Word Bands come with 12 different saying in one package - all appropriate for Chirstmas wishes. So 12 cards per package!
Hope this gives you some ideas for using the Harlequin stencil to create cards or tags. My friend Richele Christensen has a fabulous Christmas card on her blog using the stencils - check it out here.
giveaway is now closed
paula







